Watlow Electric EZ-ZONE PM Скачать руководство пользователя страница 109

Страница: 109 / 181

Watlow EZ-ZONE

PM Integrated Controller

•

106

•

Chapter 7 Profiling Page

Profiling Parameters

[``p1]]
[prof]

Profile (1 to 4)

[```1]

[``P1]

Profile [1 to 4] Step (1 to 40)

[s;typ]

Step Type

[t;SP1]

Target Set Point Loop 1

[t;SP2]

Target Set Point Loop 2

[hoUr]

Hours

[Min]

Minutes

[`SEC]

Seconds

[rate]

Rate

[w;pi]

Wait For Process Instance

[W;P1]

Wait For Process 1

[w;E1]

Wait For Event 1

[WE;2]

Wait for Event 2

[dow]

Day of Week

[``js]

Jump Step

[``jC]

Jump Count

[`EnD]

End Type

[Ent1]

Event 1

[Ent2]

Event 2

Ending a Profile from the Operations Page

1. Navigate to the Operations Page and then the Profile Status menu. From the Home Page, press and hold

the

or Down

key for approximately three seconds where the upper display will show

[``ai]

and the

lower display will show

[oper]

2. Press the Up

or Down

key to navigate to the Profile Status

[ p ;sta ]

menu.

3. Press the Advance Key

‰

to enter this menu. The upper display will show

[```1]

and the lower display

will show

[ p ;str]

4. Press the Advance Key

‰

to select the Profile Action Request. The upper display will show

[none]

and

the lower display will show

[ p ;aCr]

6. Press the Up

or Down

keys to select the End. The upper display will show

[`end ]

and the lower

display will show

[ p ;aCr]

7. Press the Advance Key

‰

to end the Profile.

8. Return to the Home Page by pressing and holding the Infinity Key

for approximately three seconds.

Starting a Profile from the Home Page

1. When at the Home Page, press the Advance Key

‰

to locate Profile Start and select the file or step num-

ber to start. The upper display will show

[```1]

and the lower display will show

[ p ;st1]

2. Press the Up

or Down

key to choose the file or step number.

3. Press the Advance Key

‰

to select the Profile Action Request. The upper display will show [none] and

the lower display will show

[ p ;aC1]

4. Press the Up

or Down

keys to select the Profile Start. The upper display will show

[Prof]

and the

lower display will show

[ p ;aC1]

5. Press the Infinity Key to return Home. The Profile will Start

Ending a Profile from the Home Page

1. Press the Advance Key

‰

to select the Profile Action Request. The upper display will show [none] and

the lower display will show

[ p ;aC1]

2. Press the Up

or Down

keys to select the End. The upper display will show

[~End ]

and the lower

display will show

[ p ;aC1]

3. Press the Infinity Key to return Home. The Profile will End.

Содержание EZ-ZONE PM






















































































































































































Результаты поиска

Содержание EZ-ZONE PM

Отзывы:

Watlow Electric EZ-ZONE PM, Руководство пользователя, Страница: 109 / 181

Результаты поиска

Содержание EZ-ZONE PM

Отзывы: