Waters Xevo TQD Скачать руководство пользователя страница 54

Страница: 54 / 250

3-2

Changing the Mode of Operation

ESI mode

The following sections explain how to install and remove an ESI probe. For

further details on running ESI applications, see

page 1-9

Installing the ESI probe

Required material

Chemical-resistant, powder-free gloves

To install the ESI probe:

1. Prepare the instrument for working on the source (see

page 4-7

2. Remove the protective sleeve, if fitted, from the ESI probe tip.

Warning:

The LC system connections, ESI probe, and source can

be contaminated with biohazardous and/or toxic materials. Always

wear chemical-resistant, powder-free gloves while performing this

procedure.

Warning:

To avoid electric shock, ensure that the instrument is

prepared for working on the source before commencing this procedure.

Warning:

The ESI probe tip is sharp. To avoid puncture wounds,

handle it with care.

Содержание Xevo TQD


























































































































































































































































Результаты поиска

Содержание Xevo TQD

Отзывы:

Похожие инструкции для Xevo TQD

Бренды по названию

Популярные бренды

Waters Xevo TQD, Руководство оператора, обзор и техническое обслуживание

Результаты поиска

Содержание Xevo TQD

Отзывы:

Похожие инструкции для Xevo TQD

Бренды по названию

Популярные бренды