Waters Xevo TQD Скачать руководство пользователя страница 50

Страница: 50 / 250

2-8

Preparing for Operation

Purging the infusion pump

Whenever you replace a solution bottle, purge the infusion pump with the

solution that you are going to use next. See the mass spectrometer’s online

Help for details.

Requirement:

Ensure that the end of the tubing is fully submerged in the

solvent in the wash reservoir.

Tip:

Depending on the solutions used, the instrument’s solvent delivery

system can require more than one purge cycle to minimize carryover.

Rebooting the instrument

The reset button causes the mass spectrometer to reboot.
Reboot the instrument when either of these conditions applies:

•

Immediately following a software upgrade.

•

MassLynx software fails to initialize.

To reboot the instrument:

1. Ensure that MassLynx software is closed.

2. Insert a short length (7.5 cm) of PEEK™ tubing, or similar object, into

the reset button aperture at the top, right-hand side of the instrument’s

front panel.

TP03415

Reset button aperture

Содержание Xevo TQD


























































































































































































































































Результаты поиска

Содержание Xevo TQD

Отзывы:

Похожие инструкции для Xevo TQD

Бренды по названию

Популярные бренды

Waters Xevo TQD, Руководство оператора, обзор и техническое обслуживание

Результаты поиска

Содержание Xevo TQD

Отзывы:

Похожие инструкции для Xevo TQD

Бренды по названию

Популярные бренды