Waters Xevo TQD Скачать руководство пользователя страница 127

Страница: 127 / 250

Cleaning the ion block assembly

4-51

20. Remove the extraction cone handle insulator from the extraction cone

handle.

21. Remove the extraction cone seal from the ion block.

Cleaning the ion block components

Required materials

•

Chemical-resistant, powder-free gloves.

•

Appropriately sized glass vessels in which to completely immerse

components when cleaning. Use only glassware not previously cleaned

with surfactants.

•

HPLC-grade (or better) methanol.

•

HPLC-grade (or better) water.

•

Formic acid.

•

Ultrasonic bath.

•

Source of oil-free, inert gas (for example, nitrogen) for drying (air-drying

optional).

•

Wash bottle containing HPLC-grade (or better) 1:1 methanol/water.

•

Large beaker.

Extraction cone seal

Содержание Xevo TQD


























































































































































































































































Результаты поиска

Содержание Xevo TQD

Отзывы:

Похожие инструкции для Xevo TQD

Бренды по названию

Популярные бренды

Waters Xevo TQD, Руководство оператора, обзор и техническое обслуживание

Результаты поиска

Содержание Xevo TQD

Отзывы:

Похожие инструкции для Xevo TQD

Бренды по названию

Популярные бренды