Waters Otto SPEcialist PPM Скачать руководство пользователя страница 5

Страница: 5 / 50

interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.

Electrical power safety notice

Do not position the device so that it is difficult to disconnect the power cord.

Equipment misuse notice

If equipment is used in a manner not specified by its manufacturer, the protection provided by the
equipment may be impaired.

Safety advisories

Consult the "Safety advisories" appendix in this publication for a comprehensive list of warning
advisories and notices.

Operating the device

When operating the device, follow standard quality-control (QC) procedures and the guidelines
presented in this section.

Applicable symbols

The following symbols can be present on the device, system, or packaging.

Symbol

Definition

Manufacturer

Date of manufacture

Authorized representative of the European
Community

Confirms that a manufactured product complies
with all applicable European Community
directives

Australia EMC compliant

July 1, 2021, 715006867 Ver. 01

Page v

Содержание Otto SPEcialist PPM


















































Результаты поиска

Содержание Otto SPEcialist PPM

Отзывы:

Похожие инструкции для Otto SPEcialist PPM

Бренды по названию

Популярные бренды

Waters Otto SPEcialist PPM, Обзор и руководство по обслуживанию

Результаты поиска

Содержание Otto SPEcialist PPM

Отзывы:

Похожие инструкции для Otto SPEcialist PPM

Бренды по названию

Популярные бренды