Waters Otto SPEcialist PPM страница 45 Скачать руководство пользователя

Страница: 45 / 50

Warning:

The user shall be made aware that if the equipment is used in a manner not

specified by the manufacturer, the protection provided by the equipment may be
impaired.

Avertissement :

L’utilisateur doit être informé que si le matériel est utilisé d’une

façon non spécifiée par le fabricant, la protection assurée par le matériel risque d’être
défectueuses.

Warnung:

Der Benutzer wird darauf aufmerksam gemacht, dass bei unsachgemäßer

Verwendung des Gerätes die eingebauten Sicherheitseinrichtungen unter Umständen
nicht ordnungsgemäß funktionieren.

Avvertenza:

si rende noto all'utente che l'eventuale utilizzo dell'apparecchiatura

secondo modalità non previste dal produttore può compromettere la protezione offerta
dall'apparecchiatura.

Advertencia:

el usuario deberá saber que si el equipo se utiliza de forma distinta a la

especificada por el fabricante, las medidas de protección del equipo podrían ser
insuficientes.

警告：

使用者必

须

非常清楚如果

设备

不是按照制造厂商指定的方式使用，那么

该设备

所提供的保

护

将被削弱。

警告：

使用者必須非常清楚如果設備不是按照製造廠商指定的方式使用，那麼該設備

所提供的保護將被消弱。

경고

제조업체가

명시하지

않은

방식으로

장비를

사용할

경우

장비가

제공하는

보호

수

단이

제대로

작동하지

않을

수

있다는

점을

사용자에게

반드시

인식시켜야

합니다

警告

ユーザーは、製造元により指定されていない方法で機器を使用すると、機器が

提供している保証が無効になる可能性があることに注意して下さい。

A.6 Warnings that address the replacement of fuses

The following warnings pertain to instruments and devices equipped with user-replaceable fuses.
Information describing fuse types and ratings sometimes, but not always, appears on the
instrument or device.

Finding fuse types and ratings when that information appears on the instrument
or device:

Warning:

To protect against fire, replace fuses with those of the type and rating

printed on panels adjacent to instrument fuse covers.

July 1, 2021, 715006867 Ver. 01

Page 45

Содержание Otto SPEcialist PPM


















































Результаты поиска

Содержание Otto SPEcialist PPM

Отзывы:

Похожие инструкции для Otto SPEcialist PPM

Бренды по названию

Популярные бренды

Waters Otto SPEcialist PPM, Обзор и руководство по обслуживанию

Результаты поиска

Содержание Otto SPEcialist PPM

Отзывы:

Похожие инструкции для Otto SPEcialist PPM

Бренды по названию

Популярные бренды