Waters ACQUITY UPC2 Скачать руководство пользователя страница 33

Страница: 33 / 84

Starting the detector

8. Press the power switch on the front panel to power-on the detector.

Result:

The detector runs a series of startup diagnostic tests while the

lamp LED blinks green. The lamp LED shows steady green when the

lamp is ignited.

9. When the lamp LED is steady green, download an instrument or inlet

method in the Empower or MassLynx software.

Result:

The console displays messages and visual signals.

10. For best results, wait one hour for the detector to stabilize before

acquiring data.

Monitoring detector LEDs

Light emitting diodes on the detector indicate its state of functioning.

Power LED

The power LED, to the left-hand side of the detector’s front panel, indicates

when the detector is powered-on or powered-off.

Lamp LED

The lamp LED, to the right of the power LED, indicates the lamp status.

Lamp LED indications:

LED mode and color

Description

Unlit

Indicates the detector lamp is extinguished.

Constant green

Indicates the detector lamp is ignited.

Flashing Green

Indicates the detector is initializing or

calibrating.

Flashing red

Indicates an error stopped the detector.

Information regarding the error that caused the

failure can be found in the console.

Constant red

Indicates a detector failure that prevents further

operation. Power-off the detector, and then

power-on. If the LED is still steady red, contact

your Waters service representative.

Содержание ACQUITY UPC2




















































































Результаты поиска

Содержание ACQUITY UPC2

Отзывы:

Waters ACQUITY UPC2, Обзор и руководство по обслуживанию, Страница: 33 / 84

Результаты поиска

Содержание ACQUITY UPC2

Отзывы: