Waters ACQUITY CM-30S Скачать руководство пользователя страница 39

Страница: 39 / 146

CM-30S control panel

October 7, 2014, 715004178 Rev. B

CM-30S control panel

If Empower

software controls the system, the CM-30S’s control panel

appears at the bottom of the Run Samples page. If MassLynx

software

controls the system, the CM-30S’s control panel appears at the bottom of the

Inlet Editor window.

CM-30S control panel:

The CM-30S control panel displays the CM-30S status, the program-selected

column, the current temperature in the column compartment, and the column

heater’s status or set point. You cannot edit CM-30S parameters while the

system is running.

Run LED indications:

LED mode and color

Description

Unlit

If both run and power LED are unlit, the CM-30S

is powered off.
If run LED is unlit and power LED is constant

green, the CM-30S is in idle mode.

Blinking green

The CM-30S is initializing or preparing to run a

method.

Constant green

The program-selected column in the CM-30S is

running a method.

Blinking red

The CM-30S is in error mode.

Solid red

The CM-30S is in error mode and requires

service.

Run LED

Current column-compartment
temperature

Status

Program-selected column (only
displays when running in
column selection mode)

Column heater status/set point

Serial number of the second column
manager (if present) in the system

Содержание ACQUITY CM-30S


















































































































































Результаты поиска

Содержание ACQUITY CM-30S

Отзывы:

Waters ACQUITY CM-30S, Обзор и руководство по обслуживанию, Страница: 39 / 146

Результаты поиска

Содержание ACQUITY CM-30S

Отзывы: