Waters ACQUITY CM-30S Скачать руководство пользователя страница 34

Страница: 34 / 146

2 Preparing and operating the CM-30S

October 7, 2014, 715004178 Rev. B

5. Plug the leak sensor connector into the receptacle on the front of the

module.

6. Power-on the CM-30S.

7. In the instrument, select System from the system tree.

8. Click Control > Leak sensors.

9. Enable the CM-30S leak sensor.

Installing the waste tubing

See also:

For additional information on configuring waste tubing, see the

Waters ACQUITY Advanced Polymer Chromatography (APC) System Site
Preparation Guide

or the

ACQUITY UPC

Site Preparation Guide

Required materials

•

Gloves: clean, powder-free, chemical-resistant

•

Waste tubing

Warning:

To avoid personal contamination with biologically

hazardous or toxic materials, wear clean, chemical-resistant,

powder-free gloves when installing or removing the waste tubing.

To avoid spreading contamination, do not allow contaminated

gloves to come in contact with uncontaminated surfaces, and

discard gloves immediately upon completing the procedure.

Leak sensor
connector receptacle

Содержание ACQUITY CM-30S


















































































































































Результаты поиска

Содержание ACQUITY CM-30S

Отзывы:

Waters ACQUITY CM-30S, Обзор и руководство по обслуживанию, Страница: 34 / 146

Результаты поиска

Содержание ACQUITY CM-30S

Отзывы: