Waters 2489 Скачать руководство пользователя страница 61

Страница: 61 / 150

June 11, 2015, 715004752 Rev. A

Page 61

3.2.4.1

Operating the Trace and Scale functions

Using the Trace function, you can display an absorbance trace for the last

minutes

(as many as 60) of detector operation.

•

When you press the TRACE key, the detector displays the absorbance acquired

over the last 30 minutes by default. It updates the trace once every 20 seconds.

•

When you press the Scale key (Shift TRACE), the detector displays the scaled

trace with T1 (ending time) displayed (–30 for the last 30 minutes) by default.

Table 3–2:

Primary and secondary function (method) parameters

Function

Screen

Type

Units

Range

Default

(Wavelength)

(Absorbanc

e screen)

Numeric

Integer 190 nm to

700 nm

254 nm

AUFS

Numeric

AUFS

0.0001 to 4.0000

2.0000

Analog rate

2 (of 4) or

2 (of 5)

Choice

(

): 10, 20, 40,

(

λλ

): 1 or 2

Filter time

constant

2 (of 4) or

2 (of 5)

Numeric

Sec

Slow

Normal

Fast

Other:

(

): 0.0125 to 5.0

(

λλ

): 0.5 to 5.0

Off to disable

filtering

Normal

(for

Other:)

1.000

Data out

(single

)

3 (of 4)

Choice

None

Absorbance A

Absorbance

Data out (dual

)

3 (of 5)

Choice

None

Absorbance A

Absorbance B

Maxplot A, B

Difference A-B

Ratio A/B

Absorbance

Autozero on

inject

3 (of 4) or

3 (of 5)

Check

box

None

Selected/

Not selected

Checked

Autozero on

changes

3 (of 4) or 3

(of 5)

Choice

None

To baseline

To zero

Disable

To zero

Voltage offset

4 (of 4) or

4 (of 5)

Numeric

Integer –2000 to

2000

Chart polarity

4 (of 4) or

4 (of 5)

Choice

None

+
–

Minimum AU

5 (of 5)

Numeric

0.0001 to 4.0000

0.1000

Minimum ratio 5 (of 5)

Numeric

None

0.00 to 999.99

0.00

Maximum

ratio

5 (of 5)

Numeric

None

0.00 to 999.99

2.00

Содержание 2489






















































































































































Результаты поиска

Содержание 2489

Отзывы:

Похожие инструкции для 2489

Бренды по названию

Популярные бренды

Waters 2489, Обзор и руководство по обслуживанию

Результаты поиска

Содержание 2489

Отзывы:

Похожие инструкции для 2489

Бренды по названию

Популярные бренды