background image

2

WARNING

!

Thermostat  installation  and  all  components  of  the 
control system shall conform to Class II circuits per 
the NEC code.

INSTALLATION 

Battery Location

2 "AA" alkaline batteries are included in the thermostat at 
the factory with a battery tag to prevent power drainage . 
Remove the battery tag to engage the batteries .
To replace batteries, set system to OFF, remove thermostat 
from wall and install the batteries in the rear along the top 
of the thermostat (see Figure 1) . For best results, use a 
premium brand "AA" alkaline battery such as Duracell

®

 or 

Energizer

®

 .

Remove Old Thermostat

A standard heat/cool thermostat consists of three basic parts:
1 .  The cover, which may be either a snap-on or hinge type .
2 .  The base, which is removed by loosening all captive 

screws .

3 .  The switching subbase, which is removed by unscrewing 

the mounting screws that hold it on the wall or adapt-
erplate . 

Before removing wires from old thermostat, 

label each wire with the terminal designation from 
which it was attached
 . Disconnect the wires from the old 
thermostat one at a time . 

Do not let wires fall back into 

the wall .

Installing New Thermostat

1 .  Pull the thermostat body off the thermostat base . Forcing 

or prying on the thermostat will cause damage to the unit .

2 .  Place base over hole in wall and mark mounting hole 

locations on wall using base as a template .

3 .  Move base out of the way . Drill mounting holes . If you are 

using existing mounting holes and the holes drilled are 
too large and do not allow you to tighten base snugly, use 
plastic screw anchors to secure the base .

4 .  Fasten base snugly to wall using the mounting holes 

shown in Figure 1 and two mounting screws . Leveling 
is for appearance only and will not affect the thermostat 
operation .

5 .  Connect wires to terminal block on base using wiring 

schematic on page 3 .

6 .  Push excess wire into wall and plug hole with a fire 

resistant material (such as fiberglass insulation) to 
prevent drafts from affecting thermostat operation .

7 .  Carefully line the thermostat up with the base and snap 

into place . 

Mounting

Hole

Mounting

Hole

Place Level
across
Mounting Tabs
(for appearance only)

Place Level

across

Mounting Tabs

(for appearance only)

+
S
-

W/E

6
L

Y2

W2

Figure 1 – Thermostat Base Multi-Stage

Rear view of thermostat

2 "AA" Batteries

Содержание TP32W03













Отзывы: