Full HD Compact Camera
WAT-30HD/CS
Operation Manual
This operation manual covers safety, camera functions, installation and the
correct operating procedure for the WAT-30HD/CS. First, we ask you to read
this operation manual thoroughly, then install and operate the WAT-30HD/CS
as advised. In addition, for future reference, we also advise safekeeping of
this manual.
If you do not understand the installation, operation or safety instructions
expressed in this manual, please contact the distributor or dealer from where
the WAT-30HD/CS was purchased. Not understanding the contents of the
operation manual sufficiently may cause damage to the camera, personal
belongings and/or result in injury.
Guide to the Safety Symbols
Symbols used in this operation manual:
“Danger”, may lead to a serious accident such as death or
injury caused by fire or electric shock.
“Warning”, may cause severe damage such as a physical injury.
“Caution”, may incur injury and cause damage to peripheral
objects in the immediate surroundings.
Cautions for Safety
The WAT-30HD/CS is designed to be used safely. If not used safely, it may
lead to a physical accident caused by fire and electric shock. Therefore,
please keep and read the, “Cautions for safety” below for protection against
accidents.
Do not disassemble and/or modify the WAT-30HD/CS.
Do not operate the WAT-30HD/CS with wet hands.
Use a stabilized power adaptor designed for DC+12V
±
10%, with a current capacity of more
than 250mA
for the
WAT-30HD/CS.
The recommended voltage is DC+12V
±
10%. Also, we
advise the Use of an “inline fuse” power line to protect the
camera and peripheral equipment, where applicable.
Do not expose the WAT-30HD/CS to wetness or high
moisture conditions.
The WAT-30HD/CS is designed and approved for indoor use
only. The WAT-30HD/CS is not water-resistant or waterproof.
If the location of the camera is outdoors or in an outdoor like
environment, we recommend that you use an outdoor camera
housing.
Protect the WAT-30HD/CS from condensation.
Keep the WAT-30HD/CS dry at all times during storage and
operation.
Should the camera not work properly, unplug the power
immediately. Then check the camera according to the
“Problems and Trouble Shooting” section.
Avoid the striking of hard objects or dropping the
WAT-30HD/CS.
The WAT-30HD/CS uses high quality electrical parts and
precision components and may inadvertently be damaged if
not cared for properly.
Do not connect any power supply directly to the video
out terminal of the unit.
Do not connect the WAT-30HD/CS with any monitor using a
video/power single transmission terminal. The WAT-30HD/CS
utilizes HD-SDI output and is not designed for use with this
type of equipment. We also advise you to read the operation
manual of the monitor you plan to use before any connections
are made.
Do not install the WAT-30HD/CS in a position subject to
direct sunlight.
Sunlight shinning directly onto the WAT-30HD/CS lens can
cause damage to the sensor.
Select a stable place for installation of the WAT-30HD/CS.
Use an appropriately rated mount durable and strong for all
installation position.
Do not move the WAT-30HD/CS with the cables
connected.
Before moving the WAT-30HD/CS, always remove the video
cable and power cable from the rear of the camera first.
Avoid using the WAT-30HD/CS near any strong electro-
magnetic field.
Avoid emission sources of electromagnetic waves when the
WAT-30HD/CS is installed into main equipment.
Problems and Trouble Shooting
If any of the following problems occur when using the WAT-30HD/CS,
An optimal picture cannot be obtained, after checking that all the cables
and connections are correctly in place.
Smoke or any unusual odor emerges from the WAT-30HD/CS
An object becomes embedded or a quantity of liquid seeps into the camera
housing.
More than the recommended voltage or/and amperage has been applied
to the WAT-30HD/CS by mistake
Anything unusual occurring to any equipment connected to the
WAT-30HD/CS
Disconnect the camera immediately according to the following
procedures:
①
Switch off the main power supply to the camera.
②
Remove the power and video cables connected to the WAT-30HD/CS.
③
Contact the distributor or dealer from which the WAT-30HD/CS was
purchased.
Contents
Using the contents figures below, check to make sure all parts are present
before use.
WAT-30HD/CS
Power and Video Cable
Description of Parts
①
IMAGE SENSOR/Sensor Window
The light receiving face of the Image sensor
(Dirt, water or oil deposits on
the image sensor will cause an unclear picture on the monitor. Attach the
lens cap to protect the lens and the sensor from contamination and
damage.)
②
LENS MOUNT
Mount of the lens (CS-mount)
③
VIDEO OUT
The terminal for SDI signal output. Use the attached power and video
cable for this purpose.
④
JOYSTICK
Joystick is for on screen display setups for functions.
⑤
POWER IN/VIDEO OUT
The terminal for power input and video signal output. Use the attached
power and video cable for this purpose.
⑥
CAMERA MOUNTING FEATURES
These mounting features are used to mount the camera.
Power Supply
Use a stabilized power adaptor designed for DC+12V
±
10%, with a current
capacity of more than 250mA.
See below for the details, for connecting to a peripheral devices.
Set-up and Operation
1
)
Ensure that the power to the WAT-30HD/CS and the peripheral
equipment is turned off before making any connections.
2
)
Remove the lens cap from the WAT-30HD/CS and attach the CS-mount
lens. Use the optional C-mount adaptor (30CMA-R) when a C-mount
lens is used.
3
)
Connect VIDEO OUT on the WAT-30HD/CS with the monitor.
4
)
Turn on the power to the WAT-30HD/CS, monitor and all other allied
equipment. When a picture cannot be obtained on the monitor, or a
strong smell of burning is present, or smoke is visible, check and follow
the procedure mentioned in the “Problems and Trouble Shooting”
section.
5
)
To bring a camera in to focus for an appropriate image.
6
)
When detailed settings are required or an adequate image is not
obtained, then set the functions on the screen by
③
Joystick.
Mounting
The WAT-30HD/CS has two bosses on both sides
featuring M2 thread and screws. Use these if the
camera is to be mounted to the B001 bracket.
Options
C-mount Adaptor (30CMA-R)
This lens mount adaptor is used to convert a
CS-mount to a C-mount.
Mounting Bracket
(
B001
)
B001 is used for mounting the WAT-30HD/CS to
stands and surfaces. The base has a U1/4”
thread for mounting on stands, and through
holes on both sides.
Mini Stand (MS50)
A convenient stand for the B001. With this
stand, the camera can be adjusted to any
desired angle.
Contact information
Design and specifications are subject to change without notice.
Watec is not responsible for any inconvenience or the attendant damages
to the video and monitoring recording equipment caused by misuse, miss-
operation or improper wiring of our equipment.
If for any reason the WAT-30HD/CS does not work properly, or if you have
any questions regarding installation or operation, please contact the
distributor or dealer from which it was purchased.
Contact information
Watec Co., Ltd.
Add.: 254-2 Nihonkoku, Daihoji, Tsuruoka- Shi,
Yamagata-Ken, 997-0017 Japan
TEL: +81-235-23-4400 FAX: +81-235-23-4409
Email: [email protected]
URL: http://www.watec.co.jp
5103Z03-Y2000003