Instructions for installing the WatcoFlex
®
Direct Drain Tee Models
IMPORTANT:
WatcoFlex
®
Before installing
, verify that this WatcoFlex
®
2
3
4
6
7
1
11
5
10
9
8
7a
7b
Installing the Flex916 & Flex924 Innovator
®
Sanitary Tee Models
90145 - Flex Inst. - 7/16
WATCO MANUFACTURING COMPANY
1220 South Powell Road • Independence, MO 64057-2724
Phone: 816-796-3900 • 800-821-8576 • Fax: 816-796-0875 • 800-399-2826
www.watcomfg.com
90145 - Flex Inst. - 7/16
WATCO MANUFACTURING COMPANY
1220 South Powell Road • Independence, MO 64057-2724
Phone: 816-796-3900 • 800-821-8576 • Fax: 816-796-0875 • 800-399-2826
www.watcomfg.com
For Assistance, call:
800-821-8576
Monday-Friday: 7:30 a.m. - 5:00 p.m. CT
For Assistance, call:
800-821-8576
Monday-Friday: 7:30 a.m. - 5:00 p.m. CT
See watcomfg.com or call for details of applicable patents and patents pending.
See watcomfg.com or call for details of applicable patents and patents pending.
Step 1:
Secure the drain tee
(Item 7a)
(Item 6)
under the tub
by screwing in the strainer body
(Item 5)
through the tub drain hole from
inside the tub.
DO NOT USE OIL-BASED PUTTY PRODUCTS: Watco
does not recommend and does not warrenty this product when oil/
petroleum based products are used when installing this product.
Step 2:
(Item 8)
(Item 7b)
.
Step 3:
from the back of the tub.
Step 4:
Screw on the retainer nut
(Item 9)
from inside the tub.
HAND TIGHTEN ONLY.
If not testing the bath waste, skip to Step 6.
Step 5:
Screw the strainer test plug
(Item 11)
into the strainer body
(Item 5)
and test
the system. Once testing is complete, remove the strainer test plug
(Item 11)
.
Step 6:
(Item 7b)
.
Step 7:
(Item 10)
with slot facing downward.
Step 8:
Install stopper assembly
(Items 1–4)
into the strainer body
(#5)
.
Note: Items
#1 thru #4 may vary depending on the type of stopper assembly being used.
Step 1:
Cut the 1
1
/
2
” Schedule 40 pipe
(#8)
and the 1
1
/
2
(#10)
to the
misalignment.
Step 2:
(#7- #10)
.
Step 3:
Secure drain elbow
(#7)
(#6)
under the tub by screwing in
the strainer body
(#5)
through the tub drain hole from inside the tub.
DO NOT USE OIL-BASED PUTTY PRODUCTS: Watco does not
recommend and does not warrenty this product when oil/petroleum based
products are used when installing this product.
Step 4:
Place foam gasket
(#12)
(#11)
.
Step 5:
back of the tub.
Step 6:
Screw on retainer nut
(#13)
from inside of tub.
HAND TIGHTEN ONLY.
If not testing the bath waste, skip to Step 8.
Step 7:
Screw the strainer test plug
(#15)
into the strainer body
(#5)
and test the system.
Once testing is complete, remove the strainer test plug
(#15)
.
Step 8:
(#11)
.
Step 9:
(#14)
with the slot facing downward.
Step 10:
Install the stopper assembly
(#1- #4)
into the strainer body
(#5)
.
Note: #1-#4 may
vary depending on the type of stopper assembly used.
