WATANABE WPMZ-1 Скачать руководство пользователя страница 55

Страница: 55 / 91

Graphical Digital Panel Meter WPMZ-1 INSTRUCTION MANUAL

IM-0882-03

13.

DISPLAY SETTINGS

This section explains the items of the display setting.
The screen displayed on the measurement screen is as follows.

・

Measure Disp:

Displayed values of Ach, Bch, calculation are displayed with numbers. It is a display method which

is displayed with large letters and real values are easy to see.

・

Level Disp:

The display values of Ach, Bch and calculation are displayed in level notation. It is a display method

which can understand the ratio to the setting upper limit value and the lower limit value at a glance.

・

Trend Disp:

Displays the display values of Ach, Bch and calculation in a trend graph. It is a display method that

makes it easy to understand the change with time of the display value.

If you press Disp key, the display is switched to next display. The order of displays is shown below.
Measurement display

⇒

Level display

⇒

Trend display

⇒

Measurement display (repeat).

Display select

Measurement display select

Select the screen to be displayed as measurement screen.

Operation:[MENU]

⇒

[Display]

⇒

[Display select]

⇒

[MeasureSelect]

Setting value (Multiple selection is possible.)

MeasureSelect

Operation

Display type

Initial display

Ach

Screen shows only display value of Ach.

1 parameter

〇

(when 1

input)

Bch

Screen shows only display value of Bch.

1 parameter

Calc

Screen shows only calculated value.

1 parameter

Ach + Comp

Screen show display value of Ach and threshold for

comparison judgment.

1 par

comparison

Bch + Comp

Screen show display value of Bch and threshold for

comparison judgment.

1 par

comparison

Calc + Comp

Screen show calculated value and threshold for

comparison judgment.

1 par

comparison

Ach + Bch

Screen show display values of Ach and Bch.

2 parameters

〇

(when 2

inputs)

Calc + Ach + Bch

Screen show calculated value and

display values of Ach and Bch.

3 parameters

*In 1ch products, some setting items are invisible.

Level display select

Select the screen to be displayed as level screen.

Operation:[MENU]

⇒

[Display]

⇒

[Display select]

⇒

[LevelSelect]

Setting value (Multiple selection is possible.)

MeasureSelect

Operation

Display type

Initial display

Ach

Screen shows only level value of Ach.

1 parameter

〇

(when 1

input)

Bch

Screen shows only level value of Bch.

1 parameter

Calc

Screen shows only calculated value as level value.

1 parameter

Ach + Bch

Screen show level values of Ach and Bch.

2 parameters

〇

(when 2

inputs)

*In 1ch products, some setting items are invisible.
*3 parameter display is not available in level display select.

Содержание WPMZ-1




























































































Результаты поиска

Содержание WPMZ-1

Отзывы:

Бренды по названию

Популярные бренды

WATANABE WPMZ-1, Инструкция по эксплуатации

Результаты поиска

Содержание WPMZ-1

Отзывы:

Бренды по названию

Популярные бренды