Wassp DRX Скачать руководство пользователя страница 14

Страница: 14 / 52

Page 26 of 102

Page 27 of 102

Doc: DRX Installation

Version: 7.1 January 2021

Doc: DRX Installation
Version: 7.1 January 2021

wassp.com

DRX INSTALLATION MANUAL

4 OPERATING THE DRX

To turn ON the DRX, short press the power key.

To turn OFF the DRX, press and hold the power key for more than 4 seconds. All
LEDs will turn off, indicating that power has been turned off.

4.1. POWER

The DRX can be powered on/off using the power button or the remote power switch.

4.2. LED STATUS

The DRX features 4 LEDS next to the power button which give a quick indication of the
status of the DRX system.

4.2.1. Startup sequence.

The boot sequence is as below:

Power

Network

Ping

Error

Power on

Booting

Starting

Process

Normal

Operation

Figure 11. Startup Sequence

4.2.2. Normal Operation LED Indications

Power

Network

Ping

Error

Figure 12. Normal Operation LED Indications

Power LED:

Off = Power OFF
On Solid = DRXApp is running

Network LED:

Off: No Link (cable not connected)
Solid: Link/Link Established
Blinking: Tx or RX traffic

Ping LED:

Off: Not pinging
Blinking: Pinging with frequency relative to ping rate (not actual ping rate).

Error LED:

Off: Normal operation
On: (While booting) system is booting
On: (After booting) Indicates an error state. All LED states should be noted and reported
to WASSP Support. See

“Appendix I - Product Registration, Support and Resources” on

page 101.

Содержание DRX





















































Результаты поиска

Содержание DRX

Отзывы:

Бренды по названию

Популярные бренды

Wassp DRX, Руководство по установке

Результаты поиска

Содержание DRX

Отзывы:

Бренды по названию

Популярные бренды