background image

-6- 

 

 

 

 

 

 

 

DG12S Check Before Operation 

1. Oil level 

Notice: Check oil level before operation each time. 

 

Open right door, You will see the oil dip stick. 

② 

Loosen oil dipstick, remove clean it with cloth, and 

then  insert  into  filter  neck  (do  not  screw).  Add 
engine oil if it is below the minimum level, ways of 

adding oil as below in (7.1.

), Finally, install and 

plug oil cap. 

Notice:  DO NOT run generator with low oil level 

or below Minimum, this will cause 
generator engine parts to damage. 

2. Fuel level 

Caution:  Please  refuel  in  a  well  ventilated  area, 

make sure there is NO cigarettes, naked 
flames or sparks when refuel. 

 

Open left door, check the fuel level indicator. 

If fuel level is low, unscrew the tank cap, fill the fuel though fuel filter. After filing 
fuel, screw back the tank cap. 

② 

If  generator  won't  operate  for  a  period  time,  drain  remaining  fuel  through  the 

discharge  hole  in  the  bottom  of  fuel  tank  (located  in  the  bottom  of  generator 
below panel). 

 

Check any damage of the battery, if damaged, please replace battery. 

OPEN 

UPPER LIMIT 

 

 

LOWER LIMIT  

Fuel volume 
indicator 

Fuel tank 
cap 

Battery 
boards 

Battery 

Содержание LDG12S
















Отзывы: