background image

SERVICING 

Cont... 

If any of the major gas components need to be replaced, such as the pilot or the gas valve, we 
recommend replacing the complete gas component assembly. The assembly is designed to be 
quickly and easily repaired with minimal inconvenience to the customer 
 

Replacing Gas Component Assembly 
 

Disconnect electricity to the appliance. (If equipped with Optional Fan Kit) 

Remove the glass door and the logs. (See installation sections page 11 and 12) 

Remove the burner tray by loosening and removing the two mounting screws located on the 
sides of the burner.  

Shut off  the gas to the appliance and disconnect the gas line to the appliance. 

If the appliance has a remote switch or thermostat, disconnect their wires at the front of the 
valve. 

Remove the four screws holding the gas component assembly plate to the appliance.  

Gently lift the assembly up and tilt the back up to clear the front of the valve from the 
opening.  

Replacing the assembly is the reverse of the above instructions. 

Disconnect power to the gas fireplace. 

Remove the fan speed mounting bracket. 

The convection blower is located at the bottom of the appliance at the back. Remove the three 
screws holding the blower. 

Rotate the blower to the left and carefully take the blower out with its back end out first. 

 Disconnect the wires from the blower. 

REPLACING MAJOR GAS COMPONENTS 

REPLACING OPTIONAL CONVECTION BLOWER 

20 

Remove the glass door, log set and the burner. 

Use a 5/8” wrench to loosen the compression fitting to the cap orifice.  

Use two 1/2” wrenches to loosen and remove the cap orifice. 

Change the orifice.  

Replace the compression fitting. 

Replace the burner and the log set. 

Test fire the appliance with the glass door off and check for gas leaks. 

Replace the glass door. 

CHANGING MAIN BURNER ORIFICE 

f i r e - p a r t s . c o m

Содержание northfire dvr36h



























Отзывы: