background image

GAS CONNECTIONS 

Before connecting the appliance to the gas supply line, double check that the appliance you 
have purchased is designed for the gas type you are using. The gas type markings are 
located on the certification label and also on the appliance’s gas valve. 
Provide adequate clearance for proper installation and checking of the gas connections.  
Have your gas supplier or a qualified gas fitter run a gas supply line into the gas fireplace. 
The line must be properly sized and fitted according to the installation codes. Up stream of 
the appliance supply connection, the fitter shall provide an easily accessible manual shut-
off valve. 
 

CAUTION:

  The  appliance and  its individual shutoff valve must be disconnected from 

the gas supply piping system during any pressure testing of that system at 
test pressures in excess of 1/2 psig (3.5 kPa). The  appliance must be 
isolated from the gas supply piping system by closing its individual manual 
shutoff valve during any pressure testing of the gas supply piping system at 
test pressures equal to or less than 1/2 psig (3.5 kPa). Failure to do so will 
damage the appliance’s gas valve. Such damage is not covered by the 
manufacturer’s warranty. 

 
Check for proper gas supply pressure by loosening the set screw on the supply pressure tap 
(marked 

IN

) on the gas valve with a small flat tip screw driver and placing a test gauge on 

the tap. 
The minimum permissible gas supply pressure is 4.5 in. w.c. (1.12 kPa) for natural gas and 
11.0 in. w.c. (2.74 kPa) for propane. Maximum gas supply pressure should never exceed 
14.0 in. w.c. (3.48 kPa) or 1/2 psi. for both natural gas and propane.  

BE SURE TO TIGHTEN THE PRESSURE TAP SET SCREW AFTER CHECKING 
THE PRESSURE. CHECK ALL GAS CONNECTIONS FOR GAS LEAKS.

 

INSTALLATION INSTRUCTIONS  

Cont... 

10 

Maximum horizontal vent length is 2ft 6”. 

Maximum of one 45º elbow is allowed. 

Maintain 1” vertical rise minimum per foot of horizontal length beyond 6”.  ie: no vertical 
rise is required for a 6” horizontal vent straight out the back of the fireplace. 

VENTING FOR REAR VENTED APPLIANCES 

Please follow the venting instructions as strictly as possible to obtain the best 
performance from the appliance. 

f i r e - p a r t s . c o m

Содержание northfire dvr36h



























Отзывы: