background image

5 April 2019

 

Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification.

 

All Dimension are in mm

………….

Copyright © 

 

4

 

Hearth & Plinth

 

FIREBOX INSTALLATION

 

HEARTH  & PLINTH CONSTRUCTION DETAILS

 

CAITEC

” 

TECHONOLGY—ROOM AIR REPLACEMENT

 

Caitec

"

 draws air from an external air source to ensure that the open fire has pre

-heated combustion air maximising efficiency while maintaining the home at con-
stant pressure equilibrium, reducing the risk of back drafting . 
Ensure that the cavity is vented to Outside fresh Air and the Warmington will take 
care of the rest. 2 x 100mm Diameter vent are required (Or equivalent to that.) 

Builder  to  supply  external  air  to  the  Cavity  and  the  “Warmington  Fire” 

takes care of the rest. 
 
NOTE : Point to consider regarding pressure differential. 

Visit the Warmington website www.warmington for 

Hebel

” 

instruction (PDF download). 

 

 

1.

 

All the dimensions are minimum.

 

2.

 

Fit  the  plinth  into  position.  If  installing  on  a  wooden  floor,  ensure  an  insulating  plinth  is  fitted  as  per  the 

specifications.  Ensure  the  plinth  is  elevated  to  allow  for  finishing  on  the  hearth.  (See  hearth  and  plinth    

details).

 

3.

 

Fit the firebox & cabinet into position.  Remove the cabinet top & bolt the firebox to the plinth or through to 

the floor with the bolting points provided on the left and right hand sides of the firebox (seismic restraints).

 

4.

 

Ensure that Hi Temp Sealant is used between the Fire and Adaptor. Bolt into position with the Bolts in the 

Left and Right Hand Sides of the Firebox.

 

5.

 

Install the Warmington Freestanding Flue System. (see page 8)

 

6.

 

Replace the top of the Freestanding cabinet. 

 

This is a general Installation guide only.  Contact a 

NZHHA Installer

” 

for installation advice.

 

Visit  www.homeheat.co.nz, choose 

members

” & 

pick your area & fire type (wood / gas etc).

 

Note: Hearth and Plinth Construction.

 

For combustible flooring an insulating hearth and plinth of 
75mm Hebel is required.

 

Plinth to be offset above hearth by the hearth finishing’s  ( e.g. 

tiles/granite/solid plaster/etc.

 

Raised hearth’s & plinth’s cantilevered must be adequately 

supported to take  the weight in accordance with the NZ    
Building Code. 

IMPORTANT NOTE: 

 

*Note: If Solid Plastering the Heat Cell Structure, it is recommended to use a fibreglass mesh with a Latex Based Plaster to 
minimise the chance of the Solid Plaster cracking. (See your Solid Plasterer for correct materials and applications). 

This is a raised & cantilevered hearth. 

See page 15 for further raised hearth 

detail.

 

Содержание SI 780 FST













Отзывы: