WarmFlow WS18 страница 58 Скачать руководство пользователя | Manualshive

Страница: 58 / 97

background image

54

If  the  flue  gas  temperature  is  above  160°C  or  a  CO  value  above  400ppm  continually  please
contact Warmflow. Please refer to Table 1 for flue gas temperatures at maximum and minimum
outputs.

Following  flue  gas  analysis,  ensure  that  the  silicone  plug  is  firmly  re-inserted  into  the
inner flue test point aperture. The weatherproof collar can then be positioned and sealed
as per Section 3.4 of this manual.

Anti Condensation valve

The  appliance  has  an  anti-condensation  valve  factory-fitted  which  must  not  be  removed  or
tampered  with  in  any  way.  The  valve  is  controlled  by  the  appliance’s  user  interface  controller
and will ensure a return temperature of 55°C to pro mote longevity of the heat exchanger.

Commissioning Records.

All  product  warranties  will  be  invalidated  if  the  appliance  is  not  commissioned  by  a Warmflow
engineer or other trained and competent engineer and the combined installation/commissioning
certificate (See Section 7 of this manual) returned to Warmflow within 30 days from the date of
installation and 90 days from the date code stamped on the appliance. A copy of this certificated
should remain with the appliance/householder.

STEP 8 - User introduction to the appliance.

After  the  installation  and  commissioning  of  the  appliance.    This  is  the  most  important
procedure  after  the  correct  installation  of  the  appliance.    A  correctly  completed  user
introduction  will  aid  the  end  user  by  making  them  aware  of  the  normal  operating
conditions and safe maintenance practices.

Identify who the main users of the appliance will be, and ensure they are presented with
the quick start guide, and this document.
Talk through the quick start guide along with the appliance, and ensure they are familiar
with  the  main  components  of  the  appliance,  how  and  when  to  fill  the  hopper,  how  and
when  to  clean  the combustion  pot  and ash  pan,  how to  use  the  user accessible  menus
within the user interface controller, and how to interpret and reset alarms.

«
...
56
57
58
59
60
...
»

Содержание WS18


































































































Отзывы:

Нет отзывов

Похожие инструкции для WS18

Бренд: Dunkirk Страницы: 32

Бренд: Raypak Страницы: 40

Бренд: Crown Boiler Страницы: 23

CSI PRIMARY AAA

Бренд: Ravenheat Страницы: 4

PD Gas Series 3

Бренд: Weil-McLain Страницы: 6

GOLD CGS 550-110-260/0107

Бренд: Weil-McLain Страницы: 64

Бренд: Lang Страницы: 17

Бренд: Tilia Страницы: 24

Бренд: Wallstar Страницы: 29

BioMass NextGen 25

Бренд: New Horizon Страницы: 19

Бренд: AFRISO Страницы: 96

Unica Max 100 kW

Бренд: Moderator Страницы: 30

Vitogas 050 ECD Series

Бренд: Viessmann Страницы: 28

ICC2 combi ZWBR 11-37 ICC2

Бренд: British Gas Страницы: 148

Бренд: VIGAS Страницы: 40

SZM W Plus 25kW

Бренд: SOLZAIMA Страницы: 53

DOMIproject F 24 D

Бренд: Ferroli Страницы: 64

Бренд: Ariterm Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды