background image

13

Operation

REMOTE CONTROL OPERATING INSTRUCTIONS

Auto off after 2 hours

1.Fan function

         Press and release the button to tum the
          fan on or off.

         Fan off. The fan memory function will
         store the current setting for the next
         time the fan is in use.

2.Speed functions

        

Press+ to increase the desired speed of

          the fan from low, medium, high.

          Press - to decrease the desired speed of
          the fan from high, medium, low.

3.Timer functions

4.Light functions

Pres and release button one time will turn the light on

Press and release button one time will turn the light off

M

II

□ Remove two remote control holder plugs from the
remote control holder (I). Note that the plugs have unique

tabs that allow them to fit only in one hole.

INSTALLING THE REMOTE CONTROL HOLDER

2hr

4hr

8hr

2hr

4hr

8hr

Auto off after 4 hours

Auto off after 8 hours

Walk away delay Turns light off after 60 seconds.

Safe Home Randomly turns the fan's light on and off to

 simulate use while away from home. Make it look like
 someone's home while you are away.

Nature Breeze Randomly cycles the fan speeds to

simulate naturally occurring air movement.

□ Attach the remote control holder (I) with the tew remote
control holder mounting screws (II).

Содержание AL01P01
















Отзывы: