Waltron AQUALERT Aqualyzer 3051 Скачать руководство пользователя | Manualshive

Страница: 28 / 70

background image

Installation

27

Waltron User Manual

3051 Hardness Analyzer

3.6.2

USER SIGNAL CONNECTIONS

The analyzer provides an External Terminal Block on the outside of the Electronics Enclosure. It
allows the operator to connect to an external device such as a sequencer or sampler, monitor the
4-20mA ouputs and monitor alarm relays. The external terminal block can be configured from
the SERVICE Screen.

Table 3.1 below shows the terminal contact labels starting with pin 1 on the left.

Figure 3.2: Electrical connections for user connections and power connections.

Table 3.1: Terminal block pin locations.

Pin Number

Terminal Label

Description

1

- Input

NO contact from an External Device to tell
the analyzer to take a measurement.

2

+ Input

3

- Signal 2

4-20mA output for Sample 2 Measurement

4

+ Signal 2

5

- Signal 1

4-20mA output for Sample 1 Measurement

6

+ Signal 1

7

COM ½

Common for Relay 1 and 2

8

OUT Relay 1

Alarm Relay 1 NO Contacts

9

OUT Relay 2

Alarm Relay 2 NO Contacts

10

OUT Relay 3

Alarm Relay 3 NO Contacts

11

OUT Relay 4

Alarm Relay 4 NO Contacts

12

COM 3/4

Common for Relay 3 and 4

«
...
26
27
28
29
30
...
»

Содержание AQUALERT Aqualyzer 3051







































































Отзывы:

Нет отзывов

Похожие инструкции для AQUALERT Aqualyzer 3051

Бренд: Keithley Страницы: 48

Бренд: Kawai Страницы: 33

Бренд: Kawai Страницы: 60

Бренд: Halcyon Страницы: 36

Bass Master Rockabilly

Бренд: K&K Sound Страницы: 2

Бренд: Energic Plus Страницы: 12

SoundTrack LxT N/Forcer

Бренд: Larson Davis Страницы: 12

Бренд: Mark-10 Страницы: 26

Бренд: Lutron Electronics Страницы: 20

Бренд: Rion Страницы: 4

Бренд: Neogen Страницы: 9

Бренд: Circutor Страницы: 48

Precision KMS7101

Бренд: Kreg Страницы: 16

Бренд: JBM Страницы: 4

Prosonic S FMU90 PROFIBUS DP

Бренд: Endress+Hauser Страницы: 110

Бренд: Tohnichi Страницы: 12

CONTISYS OBD - V3.0

Бренд: VDO Страницы: 144

Бренд: MED Associates Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды