Wallenstein WXR545PL Скачать руководство пользователя страница 12

Страница: 12 / 42

Safety

WXR545PL

Trailer Wood Splitter

Safety

2.10 Refueling Safety

Engine fuel is highly flammable. Handle with care.

Fill fuel tank outdoors.

Stop the engine before refueling. Allow engine to

cool for five minutes. Clean up spilled fuel before

restarting engine.

Do not overfill the fuel tank.

If fuel is spilled, wipe it away carefully and wait until

the fuel has dried before starting the engine.

Do not refuel the machine while

smoking or when near open flame

or sparks.

After refueling, make sure that the fuel cap is secured

to prevent spillage.

Prevent fires by keeping machine clean of

accumulated trash, grease, and debris.

2.11 Tire Safety

Failure to follow proper procedures when mounting a

tire on a wheel or rim can produce an explosion which

may result in serious injury or death.

Do not attempt to mount a tire unless you have the

proper equipment and experience to do the job.

Have a qualified tire dealer or repair service perform

required tire maintenance.

When replacing worn tires, make sure they meet the

original tire specifications. Never install undersized

tires.

2.12 Hydraulic Safety

Make sure that all the components in the hydraulic

system are kept in good condition and are clean.

Before applying pressure to the

system, make sure all components

are tight, and that lines, hoses and

couplings are not damaged.

Do not attempt any makeshift repairs to the

hydraulic lines, fittings or hoses by using tapes,

clamps or cements. The hydraulic system operates

under extremely high pressure. Such repairs can

fail suddenly and create a hazardous and unsafe

condition.

Wear proper hand and eye

protection when searching for a

high-pressure hydraulic leak. Use

a piece of wood or cardboard as

a backstop instead of hands to

isolate and identify a leak.

If injured by a concentrated high-pressure stream of

hydraulic fluid, seek medical attention immediately.

Serious infection or toxic reaction can develop from

hydraulic fluid piercing the skin surface.

Relieve pressure in the hydraulic system before

working on it.

Содержание WXR545PL











































Результаты поиска

Содержание WXR545PL

Отзывы:

Похожие инструкции для WXR545PL

Бренды по названию

Популярные бренды

Wallenstein WXR545PL, Руководство оператора

Результаты поиска

Содержание WXR545PL

Отзывы:

Похожие инструкции для WXR545PL

Бренды по названию

Популярные бренды