Wallenstein WP845 страница 56 Скачать руководство пользователя

Страница: 56 / 72

9. Service and Maintenance

Regular preventive maintenance can improve performance and
prolong the life of the machine. Machine maintenance is your
responsibility.

9.1 Service and Maintenance Safety

WARNING!

Risk of serious personal injury. Stop engine

before performing ANY service or maintenance

procedure. Reinstall all covers and shields

removed before putting machine back into

service.

W033

WARNING!

Shut down the machine and allow it to cool

before performing any service, maintenance, or

inspection procedure. Engine components and

oil may be hot enough to cause injury.
Make sure the machine is in a Safe Condition to

work on. Review Maintenance Safety beforehand.

W041

WARNING!

Wear the personal protective equipment (PPE)

that is required to complete the work safely.
For example; a hard hat, hearing protection,

protective eye wear, protective footwear,

respirator, and gloves.

W101

Place the machine in a safe condition before you start any
service or maintenance:

SAFE CONDITION

Set the tow vehicle's parking brake, turn off the engine,
and remove the ignition key.

Chock the machine wheels to prevent movement.

Remove the winch rope from the log and wind it into the
winch.

Set the hydraulic controls to neutral and wait for all
motion to stop.

Turn off the chain saw.

Turn off the engine.

Disconnect the engine spark-plug wire and keep it away
from the spark plug.

Actuate each hydraulic control to relieve the pressure.

Remove all material from the lead-in chute, log-loader
chute, splitting cradle, and splitter chute.

•

Follow good shop practices:

Keep the work area clean and dry.

Ground electrical outlets and tools.

Have adequate light for good visibility.

•

Never operate an engine inside a closed building. The
exhaust fumes may cause asphyxiation.

•

Wait for the machine to cool before starting work.
Components and liquids may be hot enough to cause
burns.

•

Never work under equipment unless it is securely
supported with blocks.

•

When replacement parts are necessary, use genuine
factory replacement parts to restore your equipment
to original specifications. The manufacturer cannot be
responsible for injuries or damages caused by use of
unapproved parts or accessories.

•

Keep a fire extinguisher and first aid kit readily accessible at
all times.

•

Do not use gasoline or diesel fuel to clean parts. Use a
regular cleanser.

•

Replace all machine guards, shields, and covers before
machine operation.

Service and Maintenance

WP845 / WP875

Trailer Firewood Processor

Содержание WP845









































































Результаты поиска

Содержание WP845

Отзывы:

Похожие инструкции для WP845

Бренды по названию

Популярные бренды

Wallenstein WP845, Руководство оператора

Результаты поиска

Содержание WP845

Отзывы:

Похожие инструкции для WP845

Бренды по названию

Популярные бренды