manualshive.com logo in svg

Wallenstein WP845, Руководство оператора

Поделиться
Скачать
Wallenstein WP845 Скачать руководство пользователя страница 49

7.  Transport

IMPORTANT!  Equipment that is transported on a public 
roadway must comply with the local laws that govern the 
safety and transport of machinery.
Before taking the machine on a public roadway, make sure it 
has the required lighting, reflectors, and markings, and that 
they are in good, working condition.
For specific requirements, contact your local transportation 
authority.

7.1  Transport Safety

• 

Make sure that the machine is securely attached to the tow 
vehicle with a retainer through the hitch. 

• 

Always attach the safety chains between the machine and 
the tow vehicle.

• 

Never allow riders on the machine.

• 

Do not exceed a safe travel speed. Slow down for rough 
terrain and cornering.

• 

Plan your route to avoid heavy traffic.

• 

Do not transport or move the machine with the engine 
running.

• 

Inspect the wheel rims for dents or damage and tighten the 
wheel lug nuts to the specified torque.  
For more information, see 

Wheel Lug Nut Torque on page 

66

.

• 

Inspect the tires for cuts or damage.

• 

Make sure the tires are filled to the specified pressure. For 
correct tire pressure, see the tire sidewall.

• 

Make sure the tow vehicle is fitted with the correct size ball-
mount hitch (2 inches).

• 

Secure all the machine guards, shields, and covers.

• 

Make sure that the fuel tank, oil tank, and hydraulic 
reservoir caps are installed and secure (to prevent spills 
during transport).

• 

Remove all debris from the machine.

• 

After the machine is prepared for transport, complete a 
circle check to make sure everything is safe, secure, and 
functions correctly.

7.2  Prepare the Machine for 

Transport

1. 

Turn off the chain saw and remove it from the holder.

2. 

If required, remove the winch rope and strap from the log.

3. 

Wind the winch rope into the winch.

4. 

Pull the 

splitter cylinder extend 

control lever up to retract 

the push block.

5. 

Move the hydraulic controls to neutral.

6. 

Stop the machine.  
For instructions, see 

Stop the Machine on page 32

.

7. 

Actuate each hydraulic control to relieve the pressure.

8. 

Remove all material from the lead-in chute, log-loader 
chute, splitting cradle, and splitter chute.

9. 

Fold up the splitter chute. 
For instructions, see 

Fold Up the Splitter Chute on page 

51

.

10. 

Fold up the lead-in and log-loader chutes. 
For instructions, see 

Fold Up the Lead-In and Log-Loader 

Chutes on page 51

.

11. 

Remove all loose tools and debris from the machine.

12. 

Attach the machine to a tow vehicle. 
For instructions, see 

Attach to a Tow Vehicle on page 52

.

WP845 / WP875
Trailer Firewood Processor

Transport

49

Содержание WP845









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды