manualshive.com logo in svg

Wallenstein WP245, Руководство оператора

Поделиться
Скачать
Wallenstein WP245 Скачать руководство пользователя страница 16

3.  Familiarization

Wallenstein Wood Processors are designed to process cut logs 
into split firewood. Logs are winched up the lead-in chute up 
to the log length guide. The customer-supplied chain saw cuts 
the log and the block falls into the splitting chamber. The wedge 
splits the wood and pushes it out the splitter chute. Power to 
drive the machine is provided through the tractor hydraulic 
system.

If the tractor does not have hydraulic circuit connections at the 
rear of the tractor to power the Wood Processor, the optional 
Hydraulic Power Pack must be installed.

3.1  To the New Operator or Owner

It is the responsibility of the owner or operator to read this 
manual and to train all other operators before they start 
working with the machine. Follow all safety instructions. 
Untrained operators are not qualified to use the machine.

1. 

Review control location, function, and movement 
directions.

2. 

Move the unit to a large open area to allow the operator 
to become familiar with control function and machine 
response. When a new operator is familiar and comfortable 
with the machine, they can proceed with the work.

3. 

Do not allow untrained operators to use the machine. They 
can endanger themselves and others or damage property 
and the machine.

IMPORTANT!  Make sure all operators understand how to 
put the machine in a safe service position before servicing 
or repairing. See 

page 7

.

3.2  Job Site Familiarization

It is the responsibility of the operator to be thoroughly familiar 
with the work site prior to starting. Prevent the chance or 
possibility of problems or accidents by avoiding unsafe 
situations. 

Some items operators should check include, but are not limited 
to:

1. 

Avoid close or cramped work spaces. Be sure there is 
enough space and clearance for the machine.

2. 

Position the machine so prevailing winds blow engine 
exhaust fumes and chain saw chips away from operator's 
station.

3. 

Choose flat and level ground and make sure the machine is 
level before operating.

4. 

Avoid muddy or soft ground.

 Familiarization

WP245 / WP275

3-Point Hitch Firewood Processor

Safety

16

Содержание WP245





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды