Wallenstein LXG300 Series Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 52

Wallenstein LXG300 Series Скачать руководство пользователя страница 32

Operating Instructions

LXG300 Series

Grapples

32

7.7 Spring-return Pivot

(LXG320S, LXG330S models)

The LXG–

S

models have a return-to-center spring pivot on the

grapple. The pivot can be locked, or left unlocked for carrying
a load or skidding. The pivot is protected by a shear bolt if
excessive torque loads occur.

The same lifting and skidding procedures can be applied to
spring return pivot, but the grapple must be manually positioned.
Follow the procedure below:

01417

Fig. 26 –

Spring-return Pivot

IMPORTANT! Make sure the pivot is UNLOCKED during
skidding. Damage to the pivot can occur if locked when
turning or contacting other objects.

7.7.1 To Unlock Pivot

•

Pull down on the grapple lock lever out of the Lock position
notch. Turning the grapple slightly may be required.

•

Rotate the lock lever around by hand to the far side and
release it into the Unlock position notch. The grapple can
now rotate freely.

•

Reverse the procedure to lock the pivot.

01429

Fig. 27 –

Grapple Pivot Lock Lever

7.7.2 To Lock Pivot

1.

Pull the grapple lock lever down out of the Unlock notch.
Rotate the lever around and release into the Lock position
notch.

2.

Rotate the grapple by hand one way or the other to one of
the 90° locking positions. Listen for a 'click' sound as the
pin locks into the hole.

01430

Fig. 28 –

Pivot Lock

«
...
30
31
32
33
34
...
»

Содержание LXG300 Series





















































Отзывы:

Нет отзывов