Wallenstein CT16B Скачать руководство пользователя страница 4

Страница: 4 / 48

1.2 Delivery Inspection Report

Wallenstein CT16B, CT24B Trailer Firewood
Conveyor

To activate warranty, register your product at:

www.wallensteinequipment.com

This form must be filled out by the dealer at the time of delivery,
then signed by the dealer and customer.

The product manuals have been received by me and I have been
thoroughly instructed as to care, adjustments, safe operation,
and applicable warranty policy.

Customer

Address

City, State/Province, ZIP/Postal Code

( )
Phone Number

Contact Name

Model

Serial Number

Delivery date

I have thoroughly instructed the buyer on the equipment care,
adjustments, safe operation, applicable warranty policy, and
have reviewed the manuals.

Dealer

Address

City, State/Province, ZIP/Postal Code

( )
Phone Number

1.2.1 Dealer Inspection Report

Engine Oil Level checked
Reduction Case Oil Level Checked
Engine Starts and Runs
All Fasteners Tight

Conveyor Drive Lubricated
Pivot Tongue Moves Freely
Review Operating and Safety Instructions

Safety Checks

All Safety Decals Installed
Guards and Shields Installed and Secured
Check Crank Jack Function
Tire Pressure Correct
Wheel Lug Torque Checked

Foreword

CT16B / CT24B

Trailer Firewood Conveyor

Содержание CT16B

















































Результаты поиска

Содержание CT16B

Отзывы:

Похожие инструкции для CT16B

Бренды по названию

Популярные бренды

Wallenstein CT16B, Руководство оператора

Результаты поиска

Содержание CT16B

Отзывы:

Похожие инструкции для CT16B

Бренды по названию

Популярные бренды