manualshive.com logo in svg

Wallenstein BXTR6438F, Руководство оператора

Поделиться
Скачать
Wallenstein BXTR6438F Скачать руководство пользователя страница 39

39

BXTR6438

4.9  Refueling:

BXTR6438

 fuel tank holds 12 gal US (50 L) of fuel, 

and is located in front of the engine. Avoid running 

the tank dry. Use the appropriate grade of fuel, and 

use caution to prevent spilling. 

Do not smoke while 

refueling.  

 
To add fuel:
1. 

Allow the engine and muffler to cool.

2.  Clean area around fuel compartment lid, and open it.
3.  Remove cap.
4. 

Using a clean funnel, fill fuel tank to 1/2" (13 mm) 

below bottom of filler neck to provide space for any 

fuel expansion. 

Do not overfill.

5. 

Install fuel fill cap securely and wipe up any spilled 

fuel.

Tank Door

Fuel Gauge

Fuel Tank

Fill Cap

Caution: Fire Hazard - No Smoking

To Prevent serious injury or death:

• 

Do not smoke while refueling

• 

Keep sparks, flames, and hot material 

away 

• 

Ensure the engine is off and cooled 

• 

Ensure muffler is cooled 

Содержание BXTR6438F





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды