manualshive.com logo in svg

Wallenstein BXT52S, Руководство оператора

Поделиться
Скачать
Wallenstein BXT52S Скачать руководство пользователя страница 13

3.  Safety Labels

 WARNING!

Replace all safety labels that are missing, 

damaged, or illegible. If a component is replaced 

and it has a safety label on it, apply a safety label 

to the new component. Operating the machine 

with missing, damaged, or illegible safety labels 

puts the operator at risk of serious injury or 

death.

W100

Learn what the safety labels mean and know the safety hazards. 
A safety label can be vertical or horizontal. Vertical safety labels 
have a top panel and a bottom panel. Horizontal safety labels 
have a left side panel and a right side panel. 
The top or left side panel shows the safety alert (possible 
hazard), and the bottom or right side panel shows the action 
message (how to prevent illness, injury, or death).

Hazard

How to avoid the 

hazard

Think SAFETY! Work SAFELY!

3.1  Replace a Safety Label

• 

Always replace safety labels that are missing or have 
become illegible. Replacement safety labels are available 
from your local Wallenstein Equipment dealer or distributor.

• 

Keep the safety labels clean and legible at all times.

• 

When a part that has a safety label on it is replaced, the 
correct safety label must be applied to the replacement 
part.

3.1.1  Conditions

• 

The installation area must be clean and dry. 

• 

The application surface must be clean and free of grease 
or oil.

• 

The ambient temperature must be above 50 °F (10 °C).

3.1.2  Tool

Use a squeegee, plastic card, or similar tool to smooth out the 
label.

3.1.3  Procedure

1. 

Identify the label location.

2. 

Peel the label off the backing paper.

3. 

Hold the label above the location where you are going to 
apply it. 
Align the edges of the label with an edge of the machine.

4. 

Start at one edge and carefully press the center of the 
adhesive side of the label onto the machine. 

5. 

Use an appropriate tool to smooth the label. Work from one 
side to the other.

6. 

If there are small air pockets:

a. Use a pin to pierce the air pocket.
b. Use a piece of the label backing paper to smooth the air 

pocket.

 Safety Labels

BXT52S 
Wood Chipper

Safety

13

Содержание BXT52S













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды