Wallenstein BX52RI Скачать руководство пользователя страница 39

Страница: 39 / 72

BX52R, BX72R, BX102R
3 PH Roller-feed Chipper

Controls

5.9 Hydraulic Winch Option

(BX102RP only)

CAUTION!

Stay clear of the winch rope while winching.

Injury from entanglement or rope burn could

occur!

W056

CAUTION!

Always make sure the area is clear of bystanders

when operating the winch. Never use the winch

to hold or secure loads.

W055

The Hydraulic Winch option is used to pull material up to the
chipper that is too large to carry. Use it to assist in lifting heavy
material onto the feed tray.

Winch Arm Extension

•

Pull out the plunger and swing the Winch Arm Extension up
out of its stowed position.

•

Release the plunger and lock the arm in the work position.

00846

Fig. 46 –

Winch Arm Extension

A control valve is used to power the winch drive. A control lever
on the winch drive gear engages/disengages the drive.

•

Disengage the drive to pull rope out.

•

Engage it to winch material in.

00855

Fig. 47 –

Hydraulic Winch

1.  Winch Control Valve
2.  Winch Drive Control
3.  Winch Arm Extension
4.  Fairlead and Winch Rope

Winch Drive

•

Push the lever away from you to disengage the winch drive.
The drive can then free wheel allowing rope to be pulled out
to the load.

•

Pull the Winch Drive Gear lever towards you to engage the
winch drive.

00847

Fig. 48 –

Winch Drive Gear

Содержание BX52RI









































































Результаты поиска

Содержание BX52RI

Отзывы:

Похожие инструкции для BX52RI

Бренды по названию

Популярные бренды

Wallenstein BX52RI, Руководство оператора

Результаты поиска

Содержание BX52RI

Отзывы:

Похожие инструкции для BX52RI

Бренды по названию

Популярные бренды