background image

23

BXT Series

6.  Operating Instructions

 CAUTION!

Park the machine so prevailing winds blow 

exhaust gases / fumes away from the operator.

W006

 CAUTION!

Risk of injury from ejected wood chips. Chipper 

rotor can expel wood chips fast enough to cause 

injury or damage. 
Direct chute discharge away from work area, 

people, animals, and objects. 

W024

 WARNING!

Never reach into the feed hopper. Doing so risks 

hands getting caught. Use a stick or branch to 

push in any material that does not move on its 

own. 
If jammed, stop the engine, wait for the rotor to 

stop, then clear the jam. 

W004

 CAUTION!

Hearing loss hazard. Prolonged 

exposure to loud noise may cause 

permanent hearing loss. Use suitable 

protection while operating the 

machine.

W016

The operator has the responsibility of being familiar with and 
following all operating and safety procedures.

Although this machine is easy to use, each operator should 
review this section to get familiar with the detailed safety and 
operating procedures.

6.1  Operating Safety

•  Do not reach into rotor or feed hopper openings when 

the machine is running. Install and secure access covers 
before starting engine.

•  Do not move or transport chipper when the rotor is 

turning.

•  Keep the working area clean and free of debris to prevent 

tripping. Operate only on level ground.

•  Do not point discharge at people, animals, or buildings. 

Rotor can expel wood chips fast enough to cause injury.

•  Be aware of the size and shape of the material being 

fed into the chipper. Crotchety branches can move in 
unpredictable ways and could cause injuries. Large 
curved pieces should be cut into smaller straighter 
sections.

•  Do not work alone. It is safer to work in pairs in case an 

emergency arises.

•  Never stand, sit or climb onto any part of the chipper 

while it is running.

•  Place chipper in a Safe Condition before servicing, 

adjusting, repairing, or unplugging.

•  Use care when feeding material into chipper. Do not 

put metal, bottles, cans, rocks, glass or other foreign 
material into wood chipper. If foreign material enters 
chipper, inspect machine for damaged or loose parts 
before resuming work.

 CAUTION!

Do not risk injury by working in an unsafe 

situation. Take steps to make the machine safe to 

work on before performing any maintenance or 

service procedure. 
Follow steps listed to put the machine in a Safe 

Condition.

W049

 SAFE CONDITION

• 

Shut off engine. Remove ignition key (if equipped).

• 

Make sure all moving parts have stopped.

• 

Disconnect battery ground (-) cable.

• 

Block or chock wheels.

Содержание 2E9US1116AS040088















































Отзывы: