background image

23 

805.281.001 

 

Date: March 22

rd

, 2017

 

Service and Maintenance 

Warning! Read “Safety Information” on page 2 before servicing the Rotator 281.

  

 

Warning! Disconnect the Rotator from AC mains power and allow cooling down for at least 10 
minutes before handling. 
 
Warning! Disconnect the attachment connection from AC mains power before handling. 
 
Warning! Refer any service operation not described in this user manual to a qualified service 
technician. 
 
Attention! Interval of inspections should be determined according to the frequency of use and 
the working scenario of the rotator.  
 
Attention! Signs of malfunction or poor operation should always lead to an inspection of the 
rotator, and the rotator should be taken out of operation until the error is eliminated. 

 
Maintenance plan 

The  results  of  all  the  regular  inspections  are  to  be  documented  and  kept  available  at  the 
company.  The  written  result  of  the  last  inspection  must  be  kept  available  at  the  site  of 
operation, e.g. by an inspection sticker  on the  rotator  showing the date of the inspection, the 
basis of the inspection and the name of the inspector. 
 

Before every use and weekly 

Every time when rigging the rotator, before running the rotator – and at least every week when 
the rotator is in use: 

 

Ensure that the rotator is correctly and safely mounted 

 

Ensure that the attached load is correctly mounted 

 

Monthly 

At regular intervals – but at least every month when the rotator is in use: 

 

Check the mounting clamp and snap hook for damages and proper fastening. 

 

Check the secure fastening of the attached lamp or electronic equipment 

 

Check the electric fastening of the lamp. 

 

Change damaged parts according to this manual. 

 

Yearly 

The rotator has to be inspected by a specialist every 12 months. 
 

Every 48 months 

The rotator should be inspected by an authorised expert every 48 months. 
 

Содержание 281


























Отзывы: