WAGO I/O System 750 XTR 750-495/040-010 Скачать руководство пользователя страница 74

Страница: 74 / 130

74 Mounting

WAGO I/O System 750 XTR

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

Figure 12: Snap the I/O Module into Place (Example)

Check that the I/O module is seated securely on the carrier rail and in the

assembly. The I/O module must not be inserted crooked or askew.

Once the I/O module has snapped into place, the electrical connections for the

data contacts and power contacts (if any) to the head station or to the preceding

and, if applicable, following I/O module are established.

Pos: 80 /Serie 750 (WAGO I/O SYSTEM)/Montieren/Demontieren/I/O-Modul entfernen (neutrales 3D) @ 35\mod_1561382848176_21.docx @ 548874 @ 3 @ 1

6.2.2

Removing the I/O Module

Remove the I/O module from the assembly by pulling the release tab.

Figure 13: Removing the I/O Module (Example)

Electrical connections for data or power jumper contacts are disconnected when

removing the I/O module.

Pos: 81 /Dokumentation allgemein/Gliederungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

Содержание I/O System 750 XTR 750-495/040-010



































































































































Результаты поиска

Содержание I/O System 750 XTR 750-495/040-010

Отзывы:

Похожие инструкции для I/O System 750 XTR 750-495/040-010

Бренды по названию

Популярные бренды

WAGO I/O System 750 XTR 750-495/040-010, Руководство пользователя

Результаты поиска

Содержание I/O System 750 XTR 750-495/040-010

Отзывы:

Похожие инструкции для I/O System 750 XTR 750-495/040-010

Бренды по названию

Популярные бренды