WAGO I/O-SYSTEM 750-666/000-003 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 166

WAGO I/O-SYSTEM 750-666/000-003 Скачать руководство пользователя страница 51

WAGO-I/O-SYSTEM 750

Connect Devices

51

750-666/000-003 4FDI/2FDO 24V/10A PROFIsafe V2 iPar

Manual

Version 1.2.0, valid from HW/SW Version 01/01

6

Connect Devices

6.1

Connecting a Conductor to the CAGE CLAMP

®

The WAGO CAGE CLAMP

®

connection is appropriate for solid, stranded and

finely stranded conductors.

Only connect one conductor to each CAGE CLAMP

®

connection!

Only one conductor may be connected to each CAGE CLAMP

®

connection.

Do not connect more than one conductor at one single connection!

If more than one conductor must be routed to one connection, these must be
connected in an up-circuit wiring assembly, for example using WAGO feed-
through terminals.

Exception:

If it is unavoidable to jointly connect 2 conductors, then you must use a ferrule to
join the wires together. The following ferrules can be used:
Length

8 mm

Nominal cross section

max.

1 mm

2

for 2 conductors with 0.5 mm

2

each

WAGO Product

216-103 or products with comparable properties.

1.

To open the CAGE CLAMP

®

insert the actuating tool into the opening

above the connection.

2.

Insert the conductor into the corresponding connection opening.

3.

To close the CAGE CLAMP

®

simply remove the tool - the conductor is

then clamped firmly in place.

Figure 18: Connecting a conductor to a CAGE CLAMP

®

«
...
49
50
51
52
53
...
»

Содержание I/O-SYSTEM 750-666/000-003







































































































































































Отзывы:

Нет отзывов