WAGO ETHERNET Accessories 852 852-0111 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 38

WAGO ETHERNET Accessories 852 852-0111 Скачать руководство пользователя страница 27

WAGO ETHERNET Accessories 852

List of Figures

27

852-0111 5 Port 100BASE-TX Industrial ECO Switch

Manual

Version 1.2.0, valid from FW/HW Version 01/06

5

Mounting

5.1

Installation site

The location selected to install the industrial ECO switch may greatly affect its
performance. When selecting a site, we recommend considering the following
rules:

•

Install the industrial ECO switch at an appropriate place. See section
Device Description” > … > “Technical Data“ for the acceptable temperature
and humidity operating ranges.

•

Fix the provided brackets at the back of the industrial ECO switch to a
carrier rail to protect the industrial ECO switch from falling.

Make sure that the heat output from the industrial ECO switch and ventilation
around it is adequate. Do not place any heavy objects on the industrial ECO
switch.

5.2

Installation on a Carrier Rail

The carrier rail must optimally support the EMC measures integrated into the
system and the shielding of the internal data bus connections.

Place the industrial ECO switch onto the carrier rail from the top and snap it into
position.

Figure 7: Snapping onto the carrier rail

5.3

Removal from DIN-Rail

To remove the device from the carrier rail, press down on the industrial ECO
switch and pull it out of the carrier rail.

«
...
25
26
27
28
29
...
»

Содержание ETHERNET Accessories 852 852-0111







































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды