WAGO 852-1305 Скачать руководство пользователя страница 31

Страница: 31 / 314

WAGO-ETHERNET-Zubehör 852

Device Description

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

4.3.2

Port LEDs

Figure 6: Port LEDs

Table 8: Legend for Figure “Port LEDs”

LED

Name

Status Description

1000M 1000BASE T Ports

LED

(1 LED for each port)

Green Port in operation at 1000 Mbit/s.

Flashes Data traffic being routed over the port.

OFF Connection in operation at less than

100 Mbit/s.

10/100

10/100BASE T Ports

LED

(1 LED for each port)

Green Lights up when the ports are linked.

Flashes Data traffic being routed over the port.

OFF No proper link established at the port.

Pos: 19.13 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwechsel--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

Содержание 852-1305



























































































































































































































































































































Результаты поиска

Содержание 852-1305

Отзывы:

Бренды по названию

Популярные бренды

WAGO 852-1305, Руководство пользователя

Результаты поиска

Содержание 852-1305

Отзывы:

Бренды по названию

Популярные бренды