WAGO 852-1305 Скачать руководство пользователя страница 176

Страница: 176 / 314

176 Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

9.3.4

DHCP Relay

Additional Information

Please refer to the section “Function Description” for more information on

“DHCP Relay” (

ynamic

ost

onfiguration

rotocol

Relay

Figure 66: WBM “DHCP Relay” Page

Table 70: WBM “DHCP Relay” Page

DHCP Relay Settings
Parameters

Default

Description

State

Disable

Select “Disable” in the selection box to disable this

function.

Enable

Select “Enable” in the selection box to enable the

“DHCP Relay”.

VLAN State

Add

Select “Add” in the selection box and enter the

VLANs on which the switch should run “DHCP

Relay”.

Valid range of VLAN IDs: 1 … 4094.

Use a comma (,) or hyphen (-) to specify individual

VLANs or VLAN ranges.

Delete

Select “Delete” in the selection box and enter the

VLANs on which the switch should not run “DHCP

Relay”.

DHCP Server IP

0.0.0.0

Enter the IP address of the DHCP server in the input

field.

DHCP Relay Status
Parameters

Default

Description

DHCP Relay State

Disable

Enable

This display field indicates if “DHCP Relay” is

enabled or disabled.

Enabled on VLAN

None

0 … 4094

This field displays if a VLAN is used.

DHCP Server IP

This field displays the IP address of the DHCP

server.

Содержание 852-1305



























































































































































































































































































































Результаты поиска

Содержание 852-1305

Отзывы:

Бренды по названию

Популярные бренды

WAGO 852-1305, Руководство пользователя

Результаты поиска

Содержание 852-1305

Отзывы:

Бренды по названию

Популярные бренды