WAGO 765-1205/0100-0000 страница 86 Скачать руководство пользователя

Страница: 86 / 102

765-1205/0100-0000

Diagnostics

Product manual | Version: 1.0.0
8DIO FLD EC DC 24V 2.0A

Parame-
ters

Datatype Description

Parame-
ter 2
Flags

UINT16

Describes the type of parameter 2

Bits 12–15 = 0

Bits 0–11 = data type index of the data type of parameter 2

0x0007: UINT32

The corresponding text parameters and formatting are de-
scribed in document ETG.2000.

Parame-
ter 2

UINT8

Event Code

Parame-
ter 3
Flags

UINT16

Describes the type of parameter 3

Bits 12–15 = 0

Bits 0–11 = data type index of the data type of parameter 3

0x0005: UINT8

The corresponding text parameters and formatting are de-
scribed in document ETG.2000.

Parame-
ter 3

UINT8

Event Qualifier

Table 67: Event Qualifier

Bit

Name

Description

Bits 6–7

Mode

0: reserved

1: single event

2: event disappears

3: event appears

Bits 4–5

Type

0: reserved

1: notification

2: warning

3: error

Bit 3

Source

0: device (remote)

1: master/port

Bits 0–2

Instance

0: unknown

1–3: reserved

4: application

5–7: reserved

See also

Emergency Error Codes [

}

86]

Events Triggered by the IO-Link Master [

}

88]

Events Triggered by the IO-Link Device [

}

89]

11.2.1.9 Emergency Error Codes

The following emergency error codes are defined in the EtherCAT specification:

Table 68: Emergency Error Codes

Emergency Error Code (hex)

Description

00xx

Error Reset or No Error

10xx

Generic Error

20xx

Current

21xx

Current, device input side

Содержание 765-1205/0100-0000







































































































Результаты поиска

Содержание 765-1205/0100-0000

Отзывы:

Похожие инструкции для 765-1205/0100-0000

Бренды по названию

Популярные бренды

WAGO 765-1205/0100-0000, Руководство пользователя

Результаты поиска

Содержание 765-1205/0100-0000

Отзывы:

Похожие инструкции для 765-1205/0100-0000

Бренды по названию

Популярные бренды