WAGO 750-494 Series Скачать руководство пользователя страница 81

Страница: 81 / 134

WAGO-I/O-SYSTEM 750

Commissioning

750-494 3-Phase Power Measurement Module

Manual

Version 1.2.0

Figure 20: „3-Phase Power Measurement“ Dialog

The following buttons appear in the

Home (1)

ribbon:

[

Disconnect

]

Separates the fieldbus coupler/controller from the PC

[

Snapshot

]

Opens a "Save as" standard dialog to save all actual

measured values, I/O module settings and error messages

from the status bar (3) as a CSV file. In this dialog, enter a

file name and select a location to save the file, e.g. see

section "Appendix".

[

Settings

]

Opens the settings dialog.

[

Calibration

]

Opens the calibration dialog. More information is

available from the WAGO Support.

The buttons for the individual

measured value views

appear in the

menu (2)

The

status bar (3)

displays the connection icon and IP address of the fieldbus

coupler/controller or the name of the COM port. Per phase possible error

messages are shown. These are:

•

No Zero (no zero crossing)

•

VoltClip (voltage override - clipping)

•

CurClip (current override - clipping)

•

VoltSag (high measuring error - undervoltage)

Click

[Settings]

to open the "Settings" dialog in which you can configure the

application and I/O module.

Содержание 750-494 Series







































































































































Результаты поиска

Содержание 750-494 Series

Отзывы:

Похожие инструкции для 750-494 Series

Бренды по названию

Популярные бренды

WAGO 750-494 Series, Руководство пользователя

Результаты поиска

Содержание 750-494 Series

Отзывы:

Похожие инструкции для 750-494 Series

Бренды по названию

Популярные бренды