WAGO 750-482/000-001 Скачать руководство пользователя

Страница: 9 / 92

WAGO I/O System 750

Important Notes

750-482/000-001 2AI 4-20mA HART NAMUR NE43

Manual

Version 1.0.2

Important Notes

This section includes an overall summary of the most important safety

requirements and notes that are mentioned in each individual section. To protect

your health and prevent damage to devices as well, it is imperative to read and

carefully follow the safety guidelines.

2.1

Legal Bases

2.1.1

Subject to Changes

WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any

alterations or modifications. WAGO Kontakttechnik GmbH & Co. KG owns all

rights arising from the granting of patents or from the legal protection of utility

patents. Third-party products are always mentioned without any reference to

patent rights. Thus, the existence of such rights cannot be excluded.

2.1.2

Personnel Qualifications

All sequences implemented on WAGO I/O System 750 devices may only be

carried out by electrical specialists with sufficient knowledge in automation. The

specialists must be familiar with the current norms and guidelines for the devices

and automated environments.

All changes to the coupler or controller should always be carried out by qualified

personnel with sufficient skills in PLC programming.

2.1.3

Use of the 750 Series in Compliance with Underlying

Provisions

Fieldbus couplers, controllers and I/O modules found in the modular WAGO I/O

System 750 receive digital and analog signals from sensors and transmit them to

actuators or higher-level control systems. Using controllers, the signals can also

be (pre-) processed.

The devices have been developed for use in an environment that meets the IP20

protection class criteria. Protection against finger injury and solid impurities up to

12.5 mm diameter is assured; protection against water damage is not ensured.

Unless otherwise specified, operation of the devices in wet and dusty

environments is prohibited.

Operating the WAGO I/O System 750 devices in home applications without

further measures is only permitted if they meet the emission limits (emissions of

interference) according to EN 61000-6-3. You will find the relevant information in

the section “Device Description” > “Standards and Guidelines” in the manual for

the used device.

Appropriate housing (per 2014/34/EU) is required when operating the WAGO I/O

System 750 in hazardous environments. Please observe the installation

Содержание 750-482/000-001





























































































Результаты поиска

Содержание 750-482/000-001

Отзывы:

Похожие инструкции для 750-482/000-001

Бренды по названию

Популярные бренды

WAGO 750-482/000-001, Руководство пользователя

Результаты поиска

Содержание 750-482/000-001

Отзывы:

Похожие инструкции для 750-482/000-001

Бренды по названию

Популярные бренды