WAGO 750-482/000-001 Скачать руководство пользователя страница 50

Страница: 50 / 92

50 Operating Modes

WAGO I/O System 750

750-482/000-001 2AI 4-20mA HART NAMUR NE43

Manual

Version 1.0.2

Table 33: Designation of Operating Modes in PROFIBUS GSD

Operating Mode “2 AI + …”

PROFIBUS GSD

Acyclic PROFIBUS services

750-482/0..-001 2AI+opt. DPV1

Acyclic PROFIBUS Services and

Access to the Register Structure

750-482/0..-001 2AI+opt. DPV1 RA

1 HART variable per channel

750-482/0..-001 2[AI+1HV]

2 HART variables per channel

750-482/0..-001 2[AI+2HV]

3 HART variables per channel

750-482/0..-001 2[AI+3HV]

4 HART variables per channel

750-482/0..-001 2[AI+4HV]

6-Byte Mailbox

750-482/0..-001 2AI+Mailbox

When delivered, the HART I/O Module is configured in the default operating

mode as a 2-channel analog input module for 4 mA to 20 mA signals with HART

functionality, including the diagnosis according to NAMUR recommendation 43

(NE43). In this default operating mode, the I/O module can be connected to all

WAGO fieldbus couplers/controllers listed in the compatibility list in the section

“Device Description”.

In this case, HART communication is enabled by a 6-byte mailbox, which is

incorporated with the analog values in the cyclic process image

In addition, 5 further operating modes can be set up specially for connecting to

the PROFIBUS DP/V1 Fieldbus Coupler (750-333) or Fieldbus Controller

(750-833).

The Section “Description of Operation” following the section on parameterization

and a short introduction to the FDT/DTM concept and HART via PROFIBUS,

describes the individual operating modes in the appropriate applications in more

detail together with a description of the communications process and brief

commissioning instructions in each case.

8.1

Setting the Operating Mode Parameters

Depending on the fieldbus used, the HART I/O module can either be

parameterized using the “WAGO-I/O-

CHECK

” commissioning tool for WAGO-I/O-

SYSTEM 750 (Item No.: 759-302) or, for PROFIBUS, using the GSD files (device

master data) for PROFIBUS with installation program / Series 750, 752 and 755

(Item No.: 750-910).

Table 34: Setting the Operating Mode Parameters

Fieldbus Coupler/Controller Connection Parameter Setting Via:

All

WAGO-I/O-

CHECK

(759-302)

PROFIBUS DP/V1 Fieldbus Coupler

(750-333) or Fieldbus Controller (750-833)

GSD (Device Master Data)

(750-910)

see table “Compatibility List”

Содержание 750-482/000-001





























































































Результаты поиска

Содержание 750-482/000-001

Отзывы:

Похожие инструкции для 750-482/000-001

Бренды по названию

Популярные бренды

WAGO 750-482/000-001, Руководство пользователя

Результаты поиска

Содержание 750-482/000-001

Отзывы:

Похожие инструкции для 750-482/000-001

Бренды по названию

Популярные бренды