WAGO 750-482/000-001 Скачать руководство пользователя

Страница: 37 / 92

WAGO I/O System 750

Process Image 37

750-482/000-001 2AI 4-20mA HART NAMUR NE43

Manual

Version 1.0.2

Table 25: PROFIBUS Telegram, Receive Direction, 4 HART Variable per Channel

PROFIBUS Telegram Input Data (4 Variable per Channel)

Offset

Byte Designation

Remark

TV1

Tertiary variable Channel 2

29
30
31
32

QV1

Quartary variable Channel 2

33
34
35

There is no status byte in the process image for the “4 HART Variable per

Channel” operating mode.

4.6

Acyclic PROFIBUS Services

With the PROFIBUS DP/V1 Fieldbus Coupler 750-333 or Fieldbus Controller

750-833, only the two cyclic AI process values are mapped into the process

image of the connected coupler in the "Acyclic PROFIBUS services" mode.

HART-via-DPV1-services are passed on using acyclic PROFIBUS services.

Table 26: PROFIBUS Telegram, Acyclic PROFIBUS Services

PROFIBUS Telegram (Acyclic PROFIBUS Services)

Offset

Designation of Bytes

Remark

AI0

Analog input data Channel 1

1
2

AI1

Analog input data Channel 2

Depending on how the PROFIBUS coupler/controller is parameterized using the

GSD, the control and status bytes can also be transmitted via PROFIBUS in

addition to the data bytes provided by the HART I/O module.

Содержание 750-482/000-001





























































































Результаты поиска

Содержание 750-482/000-001

Отзывы:

Похожие инструкции для 750-482/000-001

Бренды по названию

Популярные бренды

WAGO 750-482/000-001, Руководство пользователя

Результаты поиска

Содержание 750-482/000-001

Отзывы:

Похожие инструкции для 750-482/000-001

Бренды по названию

Популярные бренды