WAGO 750-482/000-001 Скачать руководство пользователя страница 20

Страница: 20 / 92

20 Device Description

WAGO I/O System 750

750-482/000-001 2AI 4-20mA HART NAMUR NE43

Manual

Version 1.0.2

3.2.2

Power Jumper Contacts/Field Supply

Risk of injury due to sharp-edged blade contacts!

The blade contacts are sharp-edged. Handle the I/O module carefully to prevent

injury. Do not touch the blade contacts.

The I/O module 750-482/000-001 has 2 self-cleaning power jumper contacts that

supply and transmit power for the field side. The contacts on the left side of the

I/O module are designed as blade contacts and those on the right side as spring

contacts.

Figure 3: Power Jumper Contacts

Table 6: Legend for Figure “Power Jumper Contacts”

Contact

Type

Function

Spring contact Potential transmission (U

) for field supply

Spring contact Potential transmission (0 V) for field supply

Blade contact Potential feed-in (0 V) for field supply

Blade contact Potential feed-in (U

) for field supply

Do not exceed maximum values via power contacts!

The maximum current that can flow through the power jumper contacts is 10 A.

The power jumper contacts can be damaged and the permissible operating

temperature can be exceeded by higher current values.

When configuring the system, do not exceed the permissible maximum current

value. If there is a higher power requirement, you must use an additional supply

module to provide the field voltage.

Содержание 750-482/000-001





























































































Результаты поиска

Содержание 750-482/000-001

Отзывы:

Похожие инструкции для 750-482/000-001

Бренды по названию

Популярные бренды

WAGO 750-482/000-001, Руководство пользователя

Результаты поиска

Содержание 750-482/000-001

Отзывы:

Похожие инструкции для 750-482/000-001

Бренды по названию

Популярные бренды