manualshive.com logo in svg

WAGO 2857-570/024-001, Руководство пользователя, Страница: 11 / 120

Поделиться
Скачать
WAGO 2857-570/024-001 Скачать руководство пользователя страница 11

2857-570/024-001

Safety

Product manual | Version: 2.0.0

11

3-Phase Power Measurement Module, 1 A

• Additional heat can be produced at the clamping point by high currents and inherent

heat generated by the product. Plan a higher tenmperature range for the conductors,
or reduce inherent heat by selecting larger conductor cross-sections.

• Only one conductor may be connected to each connection point (e.g., CAGE CLAMP

®

connection).

Protection

• When working on the system (e.g., during maintenance), protect the facility part in

question from accidental or unauthorized restart.

2.3 Mechanical Safety

• Do not open the product housing.
• Before startup, please check the product for any damage that may have occurred dur-

ing shipping. Do not put the product into operation in the event of mechanical damage.

2.4 Thermal Safety

• The temperature inside the additional enclosure must not exceed the ambient tempera-

ture permitted for the mounted products.

2.5 Indirect Safety

• Do not use any contact spray for cleaning.
• Only use a dry or cloth or a clothed dampened with water to clean the product. Do not

use cleaning agents, e.g., abrasive cleaners, alcohols or acetone.

• The products are not resistant to materials having seeping and insulating properties

such as aerosols, silicones and triglycerides (found in some hand creams). If these
substances occur in the environment of the products, install the products in an addi-
tional housing that is also resistant to these substances.

• Replace any defective or damaged devices.
• Only use accessories authorized by WAGO.

Содержание 2857-570/024-001

























































































































Отзывы:

Нет отзывов