background image

11

VERSION 06/2018

ORDER NUMBER DOC 2343275

 

4.2.1  PERSONAL SAFETY EQUIPMENT
Hazard due to dangerous fluids or vapors!

Serious or fatal injuries due to inhalation, swallowing or contact with the skin or eyes.

When preparing or working with lacquer and when cleaning the device, follow the 

working instructions of the manufacturer of the lacquers, solvents, and cleaning 

agents being used.
Take the specified protective measures. In particular wear safety goggles, protective 

clothing and gloves, as well as hand protection cream if necessary.
Use a mask or breathing apparatus if necessary.
For sufficient health and environmental safety: Operate the device in a spray booth 

or on a spraying wall with the ventilation (extraction) switched on.
Wear suitable protective clothing when working with hot products.

4.2.2  SAFE HANDLING OF WAGNER SPRAY DEVICES
Hazard due to injection of lacquer or flushing agent into the skin!

The spray jet is under pressure and can cause dangerous injuries. Avoid injection of 

lacquer or flushing agents:

Never point the spray gun at people.
Never reach into the spray jet.

Ensure that the working pressure does not exceed the maximum value shown on 

the type plate.

Before any work on the device, in the event of work interruptions and malfunctions:

– Switch off the energy/compressed air supply.

– Relieve the pressure from the spray gun and device.

– Secure the spray gun against actuation.

– Disconnect the control unit from the mains.

– In the event of functional faults: remedy the fault as described in the 

"Troubleshooting" chapter.
If needed, the liquid ejection devices must be checked by experts (e.g., WAGNER 

service technician) at least every 12 months for their work-safe condition in 

accordance with DGUV regulation 100-500 Chapter 2.29 and Chapter 2.36.

– For shut down devices, the examination can be suspended until the next start-up.

In the event of skin injuries caused by lacquer or flushing agents:

Note the lacquer or flushing agent that you have been using.
Consult a doctor immediately.

Danger due to recoil forces!

Actuating the trigger can cause strong recoil forces. Thereby the user can lose his balance 

and injure himself when falling.
Avoid risk of injury from recoil forces:

Ensure that you have firm footing when operating the spray gun.

Содержание PV 100





























































Отзывы: