Wacker Neuson KRAMER 5055e страница 212 Скачать руководство пользователя

Страница: 212 / 420

5-86

BA 357-00 * 3.0 * 35700_05_Bedienung.fm

5 Operation

Working with the pallet forks

Important safety instructions for working with the pallet forks

WARNING

Accident hazard from the pallet fork arms!

Pallet fork arms can cause serious injury or death during machine travel
on public roads.

►

Remove fork arms from the pallet forks before machine
travel on public roads and transport them separately.

►

Fold up (opt) the foldable fork arms from pallet forks before travelling
on public roads.

►

Do not transport the pallet forks in a bucket.

►

Before leaving the machine, lower the pallet forks to the ground, turn
off the machine and remove the ignition key.

►

Never use bent, cracked or otherwise damaged fork arms/pallet forks!

►

Before starting work, ensure that the fork arms on the fork frame are
safely locked!

WARNING

Accident hazard and tilting hazard due to incorrect use of
attachment!

Failure to observe this can cause serious injury or death.

►

Transporting persons is prohibited.

►

Stay clear of suspended loads!

►

Lower the loader unit to transport position
before starting machine travel.

►

Adapt the travel speed to the prevailing conditions.

►

Pay attention to persons and obstacles.

►

Carefully steer the machine if the loader unit is raised.

►

Do not perform any jerky movements with the joystick.

►

The attachment is not certified for lifting gear applications.

►

Do not fasten any hooks, eyelets or other lifting gear on the
attachment.

►

Do not exceed permitted payloads (refer to the load diagram affixed on
the front window or on the left on the front trim in the cabin).

Fig. 179

Содержание KRAMER 5055e





































































































































































































































































































































































































































Результаты поиска

Содержание KRAMER 5055e

Отзывы:

Похожие инструкции для KRAMER 5055e

Бренды по названию

Популярные бренды

Wacker Neuson KRAMER 5055e, Руководство оператора

Результаты поиска

Содержание KRAMER 5055e

Отзывы:

Похожие инструкции для KRAMER 5055e

Бренды по названию

Популярные бренды