background image

2-8

BA 357-00 *  3.0 * Sicherheit_E.fm

2 Safety

Machine travel on public roads/sites

• The specific national driving license is required.
• Observe the national regulations 

(for example, the road traffic regulations) during machine travel on 
public roads/sites.

• Ensure that the vehicle is in compliance with the national regulations.
• In order not to blind other motorists, using the existing work lights 

during vehicle travel on public roads/site is prohibited.

• When crossing for example underpasses, bridges, tunnels, ensure that 

the clearance height and width is sufficient.

• The attachment fitted onto the machine must be certified for travel on 

public roads/sites (see for example, the registration documents).

• The attachment fitted onto the vehicle must be empty and in transport 

position.

• The mounted attachment must be equipped with the mandatory 

lighting and protective devices.

• Take measures against unintentional operation of the operating 

hydraulics.

• If the vehicle has different steering modes, ensure that the mandatory 

steering mode is selected.

Stopping and securing the machine

• Only turn off the machine according to the Operator’s Manual.
• Before turning off the machine, lower the work equipment/attachment 

to the ground.

• Unbuckle the seat belt only after turning off the machine.
• Before leaving the machine, secure it to prevent it from rolling away 

(for example, with the parking brake, suitable wheel chocks).

• Remove the ignition key and secure the machine against unauthorized 

operation.

• If the machine will not be used for a longer period of time, remove the 

battery connector.

Содержание KRAMER 5055e





































































































































































































































































































































































































































Отзывы:

Похожие инструкции для KRAMER 5055e