Wacker Neuson ET18 Скачать руководство пользователя страница 94

Страница: 94 / 298

4-44

OM ET18/20/24 us 1.3 * et18_20_24i400.fm

Low-load operation

Notice

The running performance of the engine can be negatively
affected if it runs at idling speed or high speed and at less than
20 % of the load.

►

Run the engine in regular operation at loads of over 20 %.

Possible consequences of low-load operation are:

•

Increased lube oil consumption.

•

Lube oil in exhaust system, and therefore engine contamination.

•

Blue smoke in exhaust gas.

Stopping the engine

Notice

Engine damage by stopping the engine after full load.

►

In order to stabilize the temperature, let the engine run at
idling speed with no load for at least 5 minutes, and then
switch it off.

Turn the starting key to “

” and remove it.

Fig. 113: Starter

Содержание ET18











































































































































































































































































































Результаты поиска

Содержание ET18

Отзывы:

Бренды по названию

Популярные бренды

Wacker Neuson ET18, Руководство оператора

Результаты поиска

Содержание ET18

Отзывы:

Бренды по названию

Популярные бренды