manualshive.com logo in svg

Wacker Neuson ET18, Руководство оператора

Поделиться
Скачать
Wacker Neuson ET18 Скачать руководство пользователя страница 114

5-20

OM ET18/20/24 us 1.3 * et18_20_24b510.fm

 

5

Telescopic travel gear (option)

WARNING

Crushing hazard due to tipping over of the machine.

Can result in severe injury or death.

►

Only perform machine operation with an extended telescopic 
travel gear.

►

Traveling with a retracted telescopic travel gear is only 
allowed for traveling very short distances. Pay attention to the 
reduced stability.

►

Retract or extend the telescopic travel gear completely.

►

Raise the boom about 20 – 30 cm (8 – 12 in) off the ground 
and position it straight ahead at the center of the machine. In 
an emergency, lower the boom immediately to increase 
stability.
This prevents the machine from tipping over in case of a hose 
rupture on the telescopic hydraulic cylinder. A hose rupture 
versmight cause the travel gear to retract and reduce stability.

WARNING

Crushing hazard when retracting the telescopic travel gear!

Can result in severe injury or death.

►

Do not allow anyone to stay in the danger zone.

Notice

In order to avoid damage to the machine when traveling through 
door frames etc.:

►

Pay attention to the width of the stabilizer blade and of the 
telescopic travel gear when traveling through passages.

►

Adjust the stabilizer blade and the telescopic travel gear to 
the same widths when operating the machine.

Содержание ET18











































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды